Backplane Tools and high speed Fabric products
AMCLB

AMCLB The Serial-RapidIO Evaluation Chassis and System uses IDT/Tundra's Tsi568 or Tsi568A switch. It allows Customers to develop software for AMCs or other S-RIO boards to replicate their hardware topology Prior to the availability of their boards.

 

For more information:


Download AMCLB Feature Sheet


AMC-SMA

AMC-SMA This is a high speed development tool for AMC.0 (.1, .2, .3, .4) with a standard 170 pin edge connector for a Yamaichi connector. It breaks out 16 SMA Connectors.

 

For more information:


Download AMC-SMA Feature Sheet


AMC-SMA Ultra 15000 Basic+

AMC-SMA Ultra 15000 The AMC-SMA Ultra 15000 Basic+ allow serdes signals to be transmitted and received for Common Options (Lanes 0-3), Fat Pipe (Lanes 4-7) and Extended Fat Pipe (Lanes 8-11) from a male AMC to individual SMAs. It plugs into ATCA Carrier/Ensemble system and acknowledge voltages, sets Geographical Addresses and JTAG & I2C interfaces.

 


AMC-SMA Ultra 9000

AMC-SMAS Ultra 9000 The platform transmits and receives all SERDES signals from an AMC card to SMAs. It provides power to the Card and accesses all the normal controls including Reset for the AMC

 


EVC80KSW0001

EVC80KSW0001 This platform features IDT’s 80KSW0001 PPS switch. It has 2 AMC socket ports, 1 SMA connector, 1 Infiniband port connector, logic headers and an I2C port.

 

For more information:


Download EVC80KSW0001 Feature Sheet


Half-Pipe

Half-Pipe The AMC card bridges AMC.4 to an Infiniband (LVDS) connector. It allows cables up to 10 meters to be connected between Serial-RapidIO system through a standard AMC.4 edge card. The single x4 lane, ports 5-8 connections are impedance controlled.

 

For more information:


Download Half-Pipe Feature Sheet


SRDP - Serial RapidIO Development Platform

SRDPThe Serial-RapidIO Evaluation Chassis and System uses IDT/Tundra’s Tsi568 or Tsi568A switch. It allows customers to develop software for AMCs or other S-RIO boards to replicate their hardware topology prior to the availability of their boards

 


SRDP2 - Serial RapidIO Development Platform Gen 2

SRDP2The Serial-RapidIO Development Platform Gen2 (SRDP2) provides a flexible prototyping, evaluation and test tool for IDT’s S-RIO Gen2 switches. It allows customers to develop software by inserting a variety of AMCs or connect other S-RIO boards to replicate their hardware topology prior to the availability of their own boards.

 

The SRDP2 is shipped with Fabric Embedded Tool’s RapidFET JTAG Standard with provides significant advanced capabilities specifically for Gen2 switch Port/Lane and SERDES control.

 


SSRP - Switchless Serial RapidIO Platform

SSRPThe SSRP is a switchless Serial-RapidIO Platform. Each kit includes schematics, user’s manual, and standoffs. Typical applications for Serial-RapidIO are system level solutions requiring QOS; mesh networking (wired or wireless); multiprocessor systems; or ASIC/SOC/IP development.

 

For more information:


Download SSRP Feature Sheet


SSS

SSS The SSS has 4 lanes through the Tsi620 switch to an AMC, SMA, and back panel Inifiniband connectors. The module has JTAG for the Tsi620. Power is from the PCI’s 3.3 Volts (there is no data or PCI support). A 12 Volt Molex connector provides power to the AMC connector. Limited quantity available!

 

For more information:


Download SSS Feature Sheet